Pacific Seacraft 44 Voyagemaker
Features and Equipment
    FEATURED EQUIPMENT
    • Cutter Rig
    • Single Handers Package for Cutter Rig
    • Chrome Plated Bronze Deck Hardware
    • Ritchie SP-5 Pedestal Steering Compass
    • SSB Radio Copper Ground System
    • Solid Boom Vang
    • Whitlock Pedestal Steering - Single Lever Throttle / Shift
    • Hot / Cold Cockpit Shower
    • Raw water Anchor / Deck Wash
    • Force 10- 3 Burner Propane Stove with Oven and Broiler
    • Epifanes varnish on interior teak woodwork.
    • Choice of Decorator Upholstery in Staterooms
    • Positive Latches on Locker Doors, Locking Sole Boards
    • Exterior woodwork oil finished
    • Hull finished in 3 coats of epoxy below the waterline.

      (Back To Top)
    CONSTRUCTION (To ABS Approved Plan Certification)
    • Hand laminated hull and deck with ½' balsa core, molded in gel coat color.
    • First hull laminate uses vinylester resin for superior blister resistance.
    • Three coats of epoxy below the waterline.
    • Standard hull & deck colors are Oyster White.
    • Choice of boot & sheer stripe colors.
    • Upper and intermediate shrouds to stainless steel chainplates and backing plates caulked and thru-bolted to the hull.
    • Lower shroud chainplates set inboard for ease of movement.
    • Solid teak rub-strake on hull.
    • Rudder with steel web frame supported by high strength manganese bronze gudgeon and closely coupled to steel reinforced integral skeg.
    • Ballast-1 1,000 pound (5.0 m) solid lead casting permanently attached w/ stainless steel keel bolts and backing plates.
    • Keel to hull joint bedded in epoxy.
    • Interior - Structural fiberglass interior unit bonded into hull with fiberglass mat and woven roving.
    • Primary bulkheads bonded into hull & deck with fiberglass then bolted in place.
    • Underside of deck, lockers and entire bilge are gel coated to prevent mildew and to facilitate cleaning.
    • All bulkhead openings for hoses and wiring are rubber grommeted to prevent chafing.
    • Deck to hull connection-Integral hull & deck flanges mated and bedded in polyurethane and fastened with stainless steel fasteners.
    • Deep bulwarks with heavy teak cap rail, hand fitted with butterfly joints.
    • Deck balsa cored. Plywood core in hardware mount areas.
    • Deck has molded-in non-skid pattern.
    • Ten year limited warranty.

      (Back To Top)

    DECK EQUIPMENT
    • All cleats, winches, turning blocks, pulpits & stanchions are thru-bolted with metal backing plates and caulked on both sides with polyurethane.
    • 30" high stainless steel double rail bow and stern pulpits with running lights and 30" high double lifeline stanchions.
    • Stainless steel boarding gates, port and starboard with double lifelines.
    • Stem fitting with 2 anchor rollers and locking pins.
    • Divided chain locker for two anchor rodes. Deck pipe to port.
    • Stern chain locker with deck pipe and stern anchor roller fairlead.
    • Chrome plated bronze deck hardware includes:
      Two Harken #56.2 STC two speed, self-tailing genoa sheet winches.
      One Harken #42.2 STC two speed, self-tailing mainsheet winch.
      Two Harken #40.2 STC self-tailing halyard and utility winches.
      Two Harken #40.2 STC two speed, self tailing secondary winches. Seventeen chrome plated bronze opening portlights.
      All hinges, hasps, jam cleats, chain pipes, deck fills, etc.
      Designated cleats for each winch.
    • Two Bomar double opening hatches and two Bomar vent hatches.
    • Four dorade vents (2ea. forward cabin and 2 ea. main salon.)
    • Stainless mast pulpits and forward dorade guards.
    • Teak loop handrails.
    • Inboard and outboard genoa tracks with Harken lead cars.
    • Harken ball bearing mainsheet traveler.
    • Spinlock rope clutches.
    • Fiberglass seahood, teak companionway sliding hatch and drop boards.
    • Stern mounted stainless steel swim ladder with teak treads and boarding gate.

      (Back To Top)
    INTERIOR
    PLUMBING
    • Three water tanks with inspection ports, approx. 105 gallons (397 liters) total.
    • Hot and cold pressure fresh water system for galley, head and shower.
    • Six gallon hot water heater from engine heat exchanger or shore power.
    • Bronze thru-hull fittings with U.L. approved bronze seacocks below the waterline, and bronze ball valves above waterline.
    • All thru-hull hose connections are double hose clamped.
    • Marine heads with holding tanks and overboard pump out.
    • Electric shower sump pump with overboard discharge.
    • Electric automatic bilge pump with Ultra float switch.
    • 25 GPM manual bilge pump in cockpit operable by helmsman.

      (Back To Top)
    ENGINE
    • Yanmar 4JH3E, four cylinder, 56 hp diesel with fresh water cooling & 160 amp alternator.
    • Clear covered engine control panel in cockpit with tachometer, engine hour meter and engine condition indicators.
    • Removable alum. fuel tank approx. 79 gallons (299 liters) w/ gauge & port.
    • Mechanical fuel pump, electric back up fuel pump.
    • Racor fuel filter with water separator.
    • Seawater strainer bulkhead mounted and water lift muffler system.
    • Three blade solid bronze propeller.

      (Back To Top)
    ELECTRICAL
    • AC/DC master power control panel with AC ammeter, AC voltmeter, polarity test circuit, 16 AC circuit breakers, DC ammeter, battery condition monitor and 20 DC circuit breakers.
    • Panel is hinged for easy access.
    • Two 4 position battery switches.
    • Tinned copper wiring throughout.
    • 110 Volt shore power system.
    • Five Lifelinedeep cycle marine batteries (95 amps each).
    • Polished chrome Cantalupidome lights and reading lights throughout interior. One adjustable chart light at navigation station.
    • Cabinetry for radar installation and electronics cabinet.
    • AC duplex receptacles with polished covers and GFI protection for 110 Volts.
    • VHF coaxial antenna cable led from masthead to navigators table.
    • Two 30 Amp. shore power cords.

      (Back To Top)
    COCKPIT
    • 7'8" long seats with contoured seat backs and seat drains.
    • Coamings have two built-in winch handle boxes, one is for shower.
    • Cockpit seat lockers for storage.
    • Lazarette hatch and vented propane locker for two tanks.
    • One 5 gallon/20 pound propane tank (empty) with stainless steel bracket.
    • Two safety harness pad eyes in forward cockpit bulkhead.
    • Whitlock Cobra pedestal wheel steering with brake & offset stainless steel pedestal guard, single ]ever throttle controls & emergency tiller.
    • Two 1-1/2" drains in cockpit sole to seacocks for fast self-bailing.
    • Removable cockpit sole w/ neoprene gasket seal for access to: engine, steering, packing gland.

      (Back To Top)
    SPARS AND RIGGING
    • Double spreader keel-stepped rig with six sheave masthead, airfoil spreaders, internal halyards and trysail track.
    • Aluminum spars with two part linear polyurethane paint.
    • Bow/foredeck light, tri-color light with strobe and spreader lights.
    • Internal conduit with VHF coax cable and wires.
    • Two single line reefs, halyards & reefs led aft. Internal 2:1 outhaul, adjustable boom topping lift and Cunningham.
    • 1 x l9 stainless steel standing rigging.
    • Color coded dacron running rigging.
    • Forged chrome bronze open body turnbuckles.
    • All Harken blocks.

      (Back To Top)
    SPECIFICATIONS
      LOA 44'-1" 13.44 m
      LWL 33'-6.5" 10.22 m
      BEAM 12'-8" 3.86 m
      DRAFT-STANDARD 6-3" 1.90 m
      SHOAL 5'-3" 1.60 m
      DISPLACEMENT 27,500 lbs 12.50 Mt
      LEAD BALLAST 11,000 lbs 5.0 Mt
      LIMIT OF POSITIVE STABILITY 141 degrees *
      SAIL AREA, Sloop 976 sq. ft. 90.71 sq. m.
      SAIL AREA, Cutter 1211 sq. ft. 112.55 sq. m.
      I = 58.88' 17.96m
      P = 50.92' 15.52 m
      J = 19.33' 5.89 m
      E = 16.0' 4.88 m
      MAST CLEARANCE 60'.0" 18.29 m
      HEADROOM 6'5" 1.96 m
      BERTHS 7 *

      Specifications subject to change without notice.
      Effective December 1, 2000.

    (Back To Top)